Home / Blog / Buying guide

How to Check Fabric Quality Before a Bulk Order

Buying guide · 5 min read · Updated 13 Nov 2026

To check fabric quality before a bulk order, approve a sample against written specifications (GSM, width, composition), test it for shrinkage and colour fastness, inspect it for faults, and then make sure the bulk lot matches the approved sample.

Below is a checklist you can run yourself with a ruler, a scale and a wash test. It does not replace laboratory testing, but it catches most common problems.

Write down the specification first

Before you see any sample, agree on a written spec: composition, GSM, width, colour, finish and construction. Without it, you cannot say later that the bulk is wrong.

Keep the approved swatch, sealed and labelled, along with a copy of the spec. This is your reference for the whole order.

GSM and width

GSM is grams per square metre. To estimate it, cut a known area, for example 10 cm by 10 cm, weigh it in grams and multiply by 100. A small kitchen scale is accurate enough for a rough check, and a GSM cutter is better.

Measure width between the selvedges, and note whether the quoted width is full width or usable width. A few centimetres of difference changes how many garments you can cut per metre.

Shrinkage and colour fastness

Natural fibres such as cotton and rayon can shrink. Mark a square, for example 20 cm by 20 cm, on a swatch, wash and dry it the way your customer will, then measure again. Do this in both warp and weft directions.

For colour fastness, wash a swatch with a white piece of cloth and check for bleeding. Rub dry and wet cloth on the surface to test crocking, and leave a piece in sunlight for a few days to see fading. Dark shades and prints need the most care.

Hand feel and appearance

Handle the fabric and compare it to the approved sample. Check the drape, stiffness, smoothness and any smell from finishing chemicals. Look at the fabric against a light to see if it is sheer, uneven or thin in patches.

Georgette, chiffon and crepe, for example, can look similar but feel different. See our georgette, chiffon and crepe guide for what to expect.

Weave and print faults

Spread the fabric on a table under good light and inspect it.

  • Weave faults: holes, slubs that are not part of the design, broken or missing threads and uneven density.
  • Dye and print faults: streaks, patches, colour out of register and shade difference from edge to centre.
  • Finishing faults: crushed areas, stains, oil marks and skew where the pattern runs off the grain.
  • Embroidery: loose threads, uneven repeats and puckering. See our embroidered fabric guide.

Lot consistency and sample approval

A good sample does not guarantee a good bulk. Colour can differ between dye lots, so ask that each colour is made in one lot, and that rolls are labelled with lot numbers.

When the bulk is ready, ask for photos and measurements from several rolls, or request a few cut pieces drawn from different rolls, and compare them with your sealed swatch.

CheckMethodCompare with
GSMWeigh a cut squareSpec and sample
WidthMeasure selvedge to selvedgeSpec
ShrinkageWash and re-measureYour care label
ColourLook in daylightSealed swatch
FaultsInspect on a tableAgreed tolerance

Agreeing terms before you pay

Agree on what happens if the bulk does not match the sample, and how claims are raised. Bulk orders with us are confirmed against a proforma invoice with advance payment, so settle the specification and sample approval before that step.

For documents and shipping, read how to import from India and our wholesale FAQ. For fabric by type, see fabrics.

Frequently asked questions

Can I test fabric quality without a lab?

Yes, for basic points such as GSM, width, shrinkage and colour bleeding. A lab report is better when a buyer, brand or regulation needs formal test results.

How much sample fabric should I ask for?

Ask for enough to cut a swatch, run wash and rub tests and make one test garment. A metre or two is common, depending on the fabric.

Who pays for samples?

Samples are chargeable (sample cost plus courier). Confirm the cost and the sample timing when you ask for a quotation.

Ready to source?

When your specification is ready, send it with the quantity on the [contact](contact) page and we will quote.